LED Red Colour 3mm Weld with Resistor

• Material: Plastic
• Standard: 3X10
• Shape: Round
• Model NO.: LED
• Length: 10mm
• Diameter: 3mm
• Brightness: Standard
• life: >30000h
• Certification: CE, RoHS
• Color: White
• Transport Package: Carton
• Specification: 3mm
• Origin: Jiangsu
• HS Code: 8541410000
• Production Capacity: 500000

Product Description

Product Description


Package Dimensions(mm)      



Notes:
1.All dimension units are millimeters.
2.All dimension tolerance is ±0.2mm unless otherwise noted.
3.An epoxy meniscus may extend about 1.5mm down the leads.
4.Burr around bottom of epoxy may be 0.5mm max.

Typical Electrical & Optical Characteristics (Ta = 25ºC)
 

ITEMS	SYMBOL	CONDITION	MIN.	TYP.	MAX.	UNIT
	VF	IF = 20mA	2.7	2.76	2.8	V
Forward Voltage
	IR	VR = 5V	---	---	1.1	μΑ
Reverse Current
	λD	IF = 20mA	520.5	526	521.9	nm
Dominant Wavelength
	IV	IF = 20mA	18900	20100	22100	mcd
Luminous Intensity

Absolute Maximum Ratings at (Ta = 25ºC)
 

ITEMS	SYMBOL	ABSOLUTE MAXIMUM RATING				UNIT
Forward Current	IF	50				mA
Peak Forward Current	IFP	220				mA
Continuous Forward Current	IL	20				mA
Reverse Voltage	VR	5				V
Power Dissipation	PD	105				mW
Operation Temperature	Topr	-40 ~ +80				ºC
Storage Temperature	Tstg	-40 ~ +80				ºC
Lead Soldering Temperature	Tsol	Max.260°C for 5 sec Max.

IFP Conditions:Pulse Width≤10msec duty≤1/10
Tsol Conditions:4mm from the base of the epoxy bulb

1.Application

This LED can be used in some common electronic equipment, such as office equipment, communication equipment, house decoration, if the LED is used in some high reliability requirements, such as air transportation, traffic control and medical equipment, must refer to the sales provided information for use.

2.storage
LED storage environment, temperature does not exceed 30ºC, relative humidity does not exceed 70%. It is recommended that the LED should be used within three months in the original packing box. If the storage time needs to be extended, it is recommended to put it in the drying box with desiccant added, or fill it with nitrogen.

3.Cleaning
Special care must be taken when cleaning colloids with chemicals, because some chemicals have damage to the surface of colloids and cause fading, such as trichloroethylene, acetone, etc. Available ethanol wipe, dipping, time at room temperature does not exceed 3 minutes.

4.Pin assembly
(1) must be 2 mm from the colloid to bend the bracket.

(2) Bracket forming must be done with a fixture or by professional personnel.

(3) Scaffold forming must be completed before welding.

(4) The pin and spacing should be consistent with the circuit board when the bracket is formed.

(5) Welding must be carried out at normal temperature. When the LED is normally welded to the PCB board, mechanical pressure on the LED pin should be avoided as far as possible.

5.weld
When welding, it must be welded below 2mm at the bottom of the colloid. When welding, it should try to avoid impregnating LED colloid. After just welding, it should avoid adding external force on the pin or shaking LED colloid.

 

Recommended welding conditions
Soldering iron welding			Wave soldering
Welding temperature		260ºC	Preheating temperature		100ºC Max
Welding time		5 Sec.Max	Warm up time		60 Sec.Max
	(one time only)		Welding temperature		260ºC Max
			Welding time		10 Sec.Max

6. Driver mode
Current drive mode of the LED
If multiple leds are connected in parallel, it is recommended to use line A and add A current limiting resistor at each LED to ensure that the brightness of the leds is consistent.

7.Esd prevention
The sharp rise of static electricity and current will cause damage to the LED. Please use anti-static devices, such as protective belts and gloves.
Note: when using the human body discharge mode HBM< 1000 v; Machine discharge mode & LT; 100 v.